Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
This post below involving Installing A Bathtub is pretty much insightful. Check it out for your own benefit and figure out what you think of it.
Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old tub is readily easily accessible, the task can relocate easily; if you need to open up a wall to get rid of the old bathtub and also place the brand-new tub, the job is much harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified on your own for the work and fit attempting it. Instead of working with a specialist to take over a halfway-completed project, it is better to think about using one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you set up a new bathtub in your bathroom if you have currently acquired a brand-new tub as well as don't require to alter the plan of your previous water supply pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing taps can be quite bothersome as a result of the restricted accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in location in between the tap and also the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are handy in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and also inspect all joints and also brand-new pipework for leakages and tighten them if essential. Fill the bathtub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the bathtub ought to wait till the tub has been used a minimum of when as this will settle it into its last position.
Preparing for the Installation
To start with, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, resulting in issues with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can split rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very taken with How to Install a Bathtub Yourself and I'm hoping you enjoyed the entire entry. Sharing is good. You never know, you could be helping someone out. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit Homepage Report this page